 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| (R) EL8186 Data Sheet October 15, 2004 FN7455.0 PRELIMINARY Micropower, Single Supply Op Amp The EL8186 is a micropower operational amplifier optimized for single supply operation at 5V and can operate down to 2.4V. Micropower performance of competing devices is achieved at the expense of seriously degrading precision, noise, speed, and output drive specifications. The EL8186 reduces supply current without sacrificing other parameters. Offset current, voltage and current noise, slew rate, and gainbandwidth product are all two to ten times better than on previous micropower op amps. The 1/f corner of the voltage noise spectrum is at 1kHz. This results in low frequency noise performance which can only be found on devices with an order of magnitude higher supply current. The EL8186 can be operated from one lithium cell or two Ni-Cd batteries. The input range goes below ground. The allNPN output stage swings to ground while sinking current no pull-down resistors are needed. Features * 65A max supply current * 1mV max offset voltage * 500pA input bias current * 0.4V/C offset voltage drift * 1MHz gain-bandwidth product * 0.15V/s slew rate * Single supply operation - Input voltage range includes ground - Output swings to ground while sinking current - No pull-down resistors are needed * Output sources and sinks 5mA load current * Open loop gain of 150kV/V Applications * Battery- or solar-powered systems * 4mA to 25mA current loops * Handheld consumer products Ordering Information PART NUMBER EL8186IW-T7 EL8186IW-T7A PACKAGE 6-Pin SOT-23 6-Pin SOT-23 TAPE & REEL 7" (3K pcs) 7" (250 pcs) PKG. DWG. # MDP0038 MDP0038 * Medical devices * Photodiode pre amps Pinout EL8186 (6-PIN SOT-23) TOP VIEW OUT 1 VS- 2 IN+ 3 +6 VS+ 5 ENABLE 4 IN- 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright (c) Intersil Americas Inc. 2004. All Rights Reserved. Elantec is a registered trademark of Elantec Semiconductor, Inc. All other trademarks mentioned are the property of their respective owners. EL8186 Absolute Maximum Ratings (TA = 25C) Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5V Differential Input Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5mA Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to VS + 0.5V Output Short-Circuit Duration . . . . . . . . . . . . . . . . . . . . . . .Indefinite Ambient Operating Temperature Range . . . . . . . . . .-40C to +85C Storage Temperature Range . . . . . . . . . . . . . . . . . .-65C to +150C CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA Electrical Specifications PARAMETER VOS V OS -----------------Time IOS IB eN iN RIN CMIR CMRR PSRR AVOL VS = 5V, 0V, VCM = 0.1V, VO = 1.4V, TA = 25C unless otherwise specified. CONDITIONS MIN TYP 0.4 TBD 0.4 0.5 fO = 1KHz fO = 1KHz 25 0.1 2 Guaranteed by CMRR test VCM = 0V to 5V VS = 2.4V to 5V VO = 0.03V to 4V, RL = 100k VO = 0.03V to 3.5V, RL = 1k 0 90 90 200 110 110 500 25 3 130 4.944 4.8 0.09 AV = 1 @ voltage < 2.0V 40 4.97 4.88 0.13 700 55 3 RL = 10 RL = 10 18 17 31 26 2.2 2.4 2 0.8 VEN = 5V VEN = 0V 0.25 -0.5 0.7 0 2 +0.5 75 10 0.16 6 200 5 2 3 MAX 1 UNIT mV V/Mo nA nA nV/Hz pA/Hz M V dB dB V/mV V/mV mV mV V V V/s kHz A A mA mA V V V A A DESCRIPTION Input Offset Voltage Long Term Input Offset Voltage Stability Input Offset Current Input Bias Current Input Noise Voltage Density Input Noise Current Density Input Resistance Input Voltage Range Common Mode Rejection Ratio Power Supply Rejection Ratio Large Signal Voltage Gain VOUT Maximum Output Voltage Swing Output low, RL = 100k Output low, RL = 1k Output high, RL = 100k Output high, RL = 1k SR GBW IS,ON IS,OFF IO+ IOVS VINH VINL IENH IENL Slew Rate Gain Bandwidth Product Supply Current, Enabled Supply Current, Disabled Short Circuit Output Current Short Circuit Output Current Minimum Supply Voltage Enable Pin High Level Enable Pin Low Level Enable Pin Input Current Enable Pin Input Current 2 FN7455.0 EL8186 Typical Performance Curves 8 VS=1.0V MAGNITUDE (dB) MAGNITUDE (dB) 4 VS=1.25V 8 4 VS=2.5V AV=100 RL=10k CL=2.7pF RF/RG=99.02 RF=221k RG=2.23k 1K VS=1.25V VS=1.0V 0 AV=1 RL=10k CL=2.7pF RF=100 RG=OPEN 1K 10K 0 -4 VS=2.5V -4 -8 100 100K 1M 10M -8 100 10K FREQUENCY (Hz) 100K 1M FREQUENCY (Hz) FIGURE 1. FREQUENCY RESPONSE vs SUPPLY VOLTAGE FIGURE 2. FREQUENCY RESPONSE vs SUPPLY VOLTAGE 60 POWER DISSIPATION (W) SUPPLY CURRENT (A) 50 40 30 20 10 0 0.45 0.4 0.35 0.3 0.25 0.2 0.15 0.1 0.05 0 JEDEC JESD51-3 LOW EFFECTIVE THERMAL CONDUCTIVITY TEST BOARD 391mW SO T2 3=2 56 5-6 C /W JA 2 2.5 3 3.5 4 4.5 5 5.5 0 25 50 75 85 100 125 150 SUPPLY VOLTAGE (V) AMBIENT TEMPERATURE (C) FIGURE 3. SUPPLY CURRENT vs SUPPLY VOLTAGE FIGURE 4. PACKAGE POWER DISSIPATION vs AMBIENT TEMPERATURE 0.5 0.45 POWER DISSIPATION (W) 0.4 0.35 0.3 0.25 0.2 0.15 0.1 0.05 0 JEDEC JESD51-7 HIGH EFFECTIVE THERMAL CONDUCTIVITY TEST BOARD 435mW SO JA = T2 323 5/ 6 0 C /W 0 25 50 75 85 100 125 150 AMBIENT TEMPERATURE (C) FIGURE 5. PACKAGE POWER DISSIPATION vs AMBIENT TEMPERATURE 3 FN7455.0 EL8186 All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation's quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 4 FN7455.0 |
Price & Availability of EL8186
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |